How to Build Top-Rope Anchors: The IDEALS Checklist
Top-Rope Anchors Learning Centre
Lesson 3 of 9
Top-Rope Anchors
SCA's letter-by-letter checklist for solid, redundant anchors, with three practice builds.
Safety note: These lessons are a reminder of skills taught in person. They do not replace hands-on instruction or supervised practice. Climbing and belaying can cause serious injury or death. Do not belay or climb without supervision until a qualified instructor has confirmed your skills, and always follow the manufacturer's instructions for your equipment.
A top-rope anchor holds everyone who climbs or is lowered on it, all day. IDEALS is SCA's checklist for building anchors that are solid, redundant and reliable. Run through it as you build, and again every time you check an anchor, your own or anyone else's. Read the story behind it in our IDEALS article.
The IDEALS Anchor Checklist Explained
| Letter | What to check |
|---|---|
| I: Integrity | Is every part trustworthy? Solid rock, a live, well-rooted tree, good bolts, gear in good condition, even your partner. Assess it before you touch any gear. |
| D: Doubled | Multiple anchor points, and every failure point doubled: carabiners, slings and connections. A single bolt or cam is rarely enough. |
| E: Equalized | No single piece does all the work: the load is shared between the points. Pre-equalized suits one direction of pull; a self-equalizing sliding X adjusts if the direction changes, a useful tool. |
| A: Angles | Aim for well under 90° between the arms. A narrow V shares the load well; a wide V loads every point harder. |
| L: Limited Extension | If one point fails, the rest of the anchor barely moves: limiter knots in a sliding X, or a pre-equalized anchor. |
| S: Sharp Edges | Check wherever slings, cord or rope touch rock. Pad sharp edges, or move the anchor. |
Build it, then check it letter by letter. IDEAL or not IDEAL?
Anchor Angles: Why a Narrow V Matters
When a load hangs from two arms, each arm pulls along its own line. The wider the angle between them, the harder each anchor point is pulled. At 120° each point holds the full load, and you have lost the benefit of having two.
Force on each anchor point as a share of the load. At 0° each point holds 50%.
Tip: build the anchor before the edge
Build the masterpoint end of the anchor first, back from the edge where you can concentrate: tie the knot, clip the lockers and look it over. Then take it to the anchor points and clip them last. You spend less time near the edge, and the build is neater.
Practice Build: Pre-Equalized Two-Bolt Anchor
- 1 Integrity: bolts and hangers solid, no heavy rust, sound rock around them.
- 2 Clip a carabiner to each bolt (locking or non-locking, locked if it's a locker), then clip a sling or cordelette of suitable length into both carabiners (a 120 cm sling is common). Pull the strands between the bolts down toward the climb, so each bolt has two strands.
- 3 Aim it: pull the bundle in the direction the rope will load it, so both arms are equally tight.
- 4 Tie an overhand on a bight with all the strands. The loops below the knot are your masterpoint.
- 5 Clip two lockers through both loops, gates opposed. Lock them.
- 6 Check it with IDEALS: angle well under 90°, masterpoint over the edge so the rope runs free.
Standard two-bolt anchor, pre-equalized
Practice Build: Sliding X with Limiter Knots
- 1 Clip a sling of suitable length into the carabiners on both bolts (locking or non-locking), gates facing out.
- 2 Pull the two strands between the bolts down and give one strand only a half twist, so it forms a small loop. Leave the other strand untwisted.
- 3 Tie an overhand limiter knot in each arm, near the masterpoint, leaving room for the masterpoint to slide a little.
- 4 Clip two lockers through the twisted strand's loop and the other strand, gates opposed. Pull down on them: they should stay trapped on the sling. If they slide off, the twist is missing, and the anchor would come apart if a bolt failed.
- 5 Check: pull the masterpoint left and right. It slides to share the load but can only drop as far as a limiter knot if a bolt fails.
Sliding X with limiter knots
A good option when the direction of pull may change, such as on a route that wanders, because the masterpoint adjusts itself. A pre-equalized anchor is simpler and extends less if a point fails, so it suits a steady direction of pull.
Practice Build: Tree Anchor
Is this tree good enough? Check all four: alive (healthy leaves or needles, no rot, fungus or large dead limbs), bigger than your thigh at the height where you tie it, well rooted in solid ground, and tested every time by pushing and wiggling it hard. A tree can look healthy and still be loose at the roots. If it moves at the base, find another anchor.
- 1 Wrap a sling or cordelette around the trunk. Low on the trunk is a good starting point because it reduces leverage. Going higher can help the set-up, on a tree that is unquestionably sound.
- 2 Turn the bar tack (the stitching on a sewn sling) or the cordelette's bend to the back of the tree, away from the knot and the load.
- 3 Bring both strands together toward the edge in a basket, and tie an overhand on a bight with both strands. The loop is your masterpoint.
- 4 Reach over the edge. If the sling is too short, use a cordelette or static rope. Pad any sharp edge.
- 5 Clip two lockers, gates opposed, and lock them.
Tree anchor: basket with a knot
Reading a Tree: Good Signs and Warning Signs
| Good signs | Warning signs: look for another anchor or back it up |
|---|---|
| Green leaves or needles right up the crown | Dead or hollow trunk, bare branches, peeling or missing bark |
| Solid wood that sounds dense when you knock it | Fungus or conks (shelf-like growths), or deep cracks in the trunk |
| Upright, with roots in deep, firm soil | A lean with lifted soil, shallow roots on a rock slab, or loose soil on a ledge |
Protect the bark: use a sling or cordelette, not the climbing rope, round the trunk. Running rope wears through bark. And tread lightly: stay on rock or bare ground, and leave plants, moss and soil around the roots as you found them. Practise all three builds with a guide on the Top-Rope Anchors course.
Common mistakes to avoid
- Running the climbing rope round the trunk, which damages the bark.
- A wide angle between the arms: over 90° loads each point far more than you think.
- A masterpoint that sits back from the edge, so the rope runs over rock.
- A tree that is too small, dead, loosely rooted, or not tested.
- The bar tack or cordelette bend inside the knot or taking the load.
- A sliding X with no twist. Without it, the masterpoint lockers can slide right off the sling if a bolt fails.
Want more Squamish climbing tips in Google? Add Squamish Climbing Academy as a preferred source.
Learn this in person
This lesson is taught hands-on with a qualified guide in:
Top-Rope Anchors · Intro & Anchors Weekend Combo
Questions and Comments
Have a question about this lesson? Share what you are working on, ask for clarification or join the conversation.
No comments yet. What would you like to know?
