How to Belay a Top Rope Climber
Intro to Climbing Learning Centre
Lesson 4 of 11
Intro to Climbing
Setting up, the PBUS belay technique, commands, and weight differences.
Safety note: These lessons are a reminder of skills taught in person. They do not replace hands-on instruction or supervised practice. Climbing and belaying can cause serious injury or death. Do not belay or climb without supervision until a qualified instructor has confirmed your skills, and always follow the manufacturer's instructions for your equipment.
The belayer is the climber's safety. On a top rope the rope runs from the climber up through the anchor and back down to the belayer, who takes in slack as the climber moves up and holds them if they fall or ask to rest. Our Intro to Rock Climbing course includes supervised belaying practice.
The top rope system. Belayer close to the base, a little to one side.
How to Set Up a Top Rope Belay Device
- 1 Stand close to the base, a little to one side of the climber's line, where you can see the climber and won't trip.
- 2 Clip in: locking carabiner through your belay loop and the belay device, rope loaded the way your guide showed you. Lock it.
- 3 Check each other with the CRASH check, then use the commands below.
The golden rule
Your brake hand never leaves the brake strand. Not to wave, scratch, fix your hair or take a photo. If you need your brake hand free, ask your guide to take over first.
Top Rope Belay Technique: Pull, Brake, Under, Slide (PBUS)
Pull, brake, under, slide. The brake hand never leaves the brake strand.
- 1 Pull: your guide hand (the hand that guides the rope, not your SCA guide) pulls the climber strand down while the brake hand pulls slack up and out of the device.
- 2 Brake: brake hand moves down to the brake position, below the device.
- 3 Under: guide hand grabs the brake strand below the brake hand.
- 4 Slide: brake hand slides up toward the device (not into it). Guide hand returns to the climber strand. Repeat.
- 5 Keep the rope snug. Take in slack as the climber moves up; no big loops.
- 6 If the climber falls or calls "Take!": pull the brake strand down firmly into the brake position and hold.
Climbing and Belaying Commands for Clear Communication
Use these exact words, and agree on the plan at the top before the climber leaves the ground. Say your partner's name first at a busy crag, and if you are ever unsure what you heard, hold the climber and ask again.
| Climber says | Belayer answers (and does) |
|---|---|
| "On belay?" | "Belay on." Checks done, slack taken in, ready to belay. |
| "Climbing." | "Climb on." Takes in slack as the climber moves up. |
| "Take!" | Pulls in all the slack, locks off in the brake position and holds the climber. Answers "Got you." |
| "Slack." | Feeds out a little rope. Brake hand stays on. |
| "Lower." | "Lowering." Lowers slowly and smoothly. |
| "Off belay." (only when standing safely on the ground) | "Belay off." Only now takes the rope out of the device. |
| "ROCK!" (anyone) | Something is falling. Move in close to the rock, don't look up, and repeat the call. |
Common mistakes to avoid
- Letting go of the brake strand, even for a second.
- Standing far back from the wall or sitting down. You can be pulled forward and lose control.
- Too much slack, which means a longer fall for the climber.
- Letting the brake hand slide right up into the device, or wrapping the rope around your hand.
- Chatting or looking at your phone instead of watching your climber.
Belaying a Heavier Climber: Ground Anchors and Added Weight
If the climber is noticeably heavier than the belayer, a fall or a "Take!" can lift the belayer off the ground. A lifted belayer can be pulled into the wall, get hurt, or lose control of the brake strand. Your guide will decide when this applies, and will set up one of these two options.
Option A (left): ground anchor, in line with the rope's pull. Option B (right): added weight.
Option A, ground anchor:
- Your guide sets up or approves a solid ground anchor: a tree, bolt or boulder.
- A sling or tether connects the ground anchor to the belayer's belay loop.
- Keep it snug. Slack lets the belayer get lifted before the tether catches.
- Keep it in line with the rope's pull toward the wall: top anchor, belayer and ground anchor in one straight line, so the belayer is not yanked up or sideways.
Option B, add weight:
- A weighted bag (for example a pack or rope bag) is attached to the belayer's harness, set up by your guide.
- The extra weight helps keep the belayer on the ground when the climber falls or sits back.
Either way, the belayer still stands close to the base, the brake hand never leaves the brake strand, and the ground anchor or weight bag becomes part of your CRASH check.
Common mistakes with weight differences
- Slack in the tether between the belayer and the ground anchor.
- A ground anchor out of line (off to the side or far behind), which pulls the belayer sideways or off balance.
- The belayer standing far from the wall. A big swing toward the wall is still a big swing, tether or not.
Want more Squamish climbing tips in Google? Add Squamish Climbing Academy as a preferred source.
Learn this in person
This lesson is taught hands-on with a qualified guide in:
Intro to Rock Climbing · Intro & Anchors Weekend Combo · Youth Climbing Camps
Questions and Comments
Have a question about this lesson? Share what you are working on, ask for clarification or join the conversation.
No comments yet. What would you like to know?
