How to Use a GRIGRI and Tie a Munter Hitch
Intro to Climbing Learning Centre
Lesson 9 of 11
Intro to Climbing
Optional
Loading and lowering with a GRIGRI, and tying a Munter hitch.
Safety note: These lessons are a reminder of skills taught in person. They do not replace hands-on instruction or supervised practice. Climbing and belaying can cause serious injury or death. Do not belay or climb without supervision until a qualified instructor has confirmed your skills, and always follow the manufacturer's instructions for your equipment.
Optional extras
Your guide may cover these if there is time and you are keen to learn more. Use this lesson to remember what you practised with your guide, not to teach yourself something new. See our Intro to Rock Climbing course for guided instruction.
How to Load a Petzl GRIGRI and Check the Rope
Loading (open) and the tug test (closed). Simplified drawing.
These notes follow Petzl's instructions for the current GRIGRI. Other assisted-braking devices, and older GRIGRI models, load and work differently, so always follow the instructions for the device in your hands.
- 1 Swing the side plate open and lay the rope round the cam, following the diagram engraved on the device: climber side to the climber symbol, brake side to the hand symbol. The brake side leaves over the wear bar.
- 2 Close the side plate. Clip a locking carabiner through the attachment hole and your belay loop, and lock it.
- 3 Test it, every time. Hold the brake strand and tug the climber side sharply: the cam should lock. If the rope runs through, it is loaded backwards. Load it again.
- 4 Brake hand on the brake strand, always. The device helps you brake, but it is not hands-free.
Common mistakes with a GRIGRI
- Loading it backwards and skipping the tug test.
- Letting go of the brake strand: "the device will catch it".
- Holding the device or a thumb on the cam, which can stop it locking.
How to Lower a Climber with a GRIGRI
Lowering with a GRIGRI (simplified drawing)
- 1 Get ready: on "Take!", take in the slack until the climber sits back on the rope. They call "Lower."
- 2 Right hand on the brake strand, below the device, with the strand over the wear bar. Grip firmly: this hand controls the speed.
- 3 Left hand on the handle: middle, ring and little fingers on it, index finger off.
- 4 Pull the handle back gradually until the rope moves. The handle releases the rope; your right hand brakes. Slow and smooth.
- 5 Too fast? Let go of the handle. The device locks. Keep your right hand on the brake strand, then start again gently.
- 6 Hands off the cam and side plates. Hold only the handle. Left-handed? Mirror the hands.
Common mistakes when lowering with a GRIGRI
- Yanking the handle wide open, or grabbing it with your whole hand.
- The brake strand not running over the wear bar.
- A loose right hand on the brake strand. Without it, the lower can run away.
- Hanging on to the handle when the climber is going too fast. Let go and the device locks.
- Gripping the body of the device or the cam, which can stop the cam from working.
How to Tie and Check a Munter Hitch
Munter hitch on a pear-shaped locker (simplified drawing)
The Munter hitch (also called the Italian hitch) is a friction knot tied on a locking carabiner. With just a rope and a pear-shaped locker you can belay or lower, which makes it a handy backup if you drop your belay device.
- 1 Use a pear-shaped (HMS) locking carabiner. Its wide end gives the hitch room to run and flip smoothly.
- 2 Make two identical loops in the rope, side by side, then fold them together like closing a book, so one loop sits behind the other.
- 3 Clip the carabiner through both loops, clip it to your belay loop, and lock it.
- 4 Check the strands. The brake strand should run on the spine side of the carabiner, away from the gate.
- 5 Test it. Hold the brake strand and pull the climber strand: the hitch should grip. Feed rope and it should run, flipping through the carabiner when the direction changes. If it will not move at all, you have probably tied a clove hitch.
- 6 Brake hand never lets go. Your guide will show you the hand position.
Common mistakes with a Munter hitch
- Using a small D-shaped carabiner, which pinches the hitch so it does not run or flip well.
- The brake strand running across the gate.
- Tying a clove hitch by mistake (it locks instead of running).
- Forgetting that a Munter twists the rope. Let the twists shake out before the next climb.
Want more Squamish climbing tips in Google? Add Squamish Climbing Academy as a preferred source.
Learn this in person
This lesson is taught hands-on with a qualified guide in:
Intro to Rock Climbing ยท Intro & Anchors Weekend Combo
Questions and Comments
Have a question about this lesson? Share what you are working on, ask for clarification or join the conversation.
No comments yet. What would you like to know?
